Nylon 610 /Polyamides
Molding and Extrusion Compound
**************************************
Copyright 2002 by Roger D. Corneliussen
**************************************
Values are from Modern Plastics Encyclopedia 99.
To jump to a particular property, click on the name listed below.
Melt
Flow
Melting
Temperature
Glass
Transition
Processing Molding Pressure
Processing Molding Temperature
Compression
Ratio
Mold
Shrinkage
Tensile
Strength
Elongation
Tensile
Yield Strength
Compressive
Strength
Flexural
Strength
Tensile
Modulus
Flexural
Modulus
Izod
Impact Strength
Hardness
Deflection
Temperature
Thermal
Expansion
Thermal
Conductivity
Specific
Gravity
Dielectric
Strength
Water
Absorption
Note:
The ASTM numbers are linked to
their descriptions on the ASTM website.
To go to the description, simply
click on the ASTM number
Melt
Flow
ASTM D1238
(gm/10 min)
--- gm /10 min
Melting
Temperature degrees C
Tm Crystalline
220 C
To go back to contents,
click on
Contents
Glass
Transition
(C)
Tg (Amorphous)
--- C
Processing
Temperature
Range Degrees F
Extrusion
445 to 485 F for injection molding
480 to 500 F for extrusion
Molding
Pressure Range ( PSI) (ksi)
1000 to 19000 psi
1 to 19 ksi
6.7 to 127 MPa
To go back to contents,
click on
Contents
Compression
Ratio
3 to 4
Mold(Linear)
Shrinkage (in/in)
ASTM D955
0.005 to 0.015 in/in
Tensile
Strength at Break
ASTM D638
10150 (dry as molded) psi
68 MPa
7250 (conditioned in 50% RH) psi
48 MPa
To go back to contents,
click on
Contents
Elongation
at break (%)
ASTM D638
70 % (dry as molded)
150% (conditioned in 50% RH)
Tensile
Yield Strength (psi)
ASTM D638
--- psi
--- MPa
Compressive
Strength (psi)
Rupture or Yield
ASTM
D695
--- psi
--- MPa
To go back to contents,
click on
Contents
Flexural
Strength (psi)
Rupture or Yield
ASTM D790
350 psi (dry as molded)
2.3 MPa
217 psi (conditioned in 50% RH)
1.4 MPa
Tensile
Modulus (psi)
ASTM D638
--- psi
--- GPa
To go to Modulus Values,
click on
Modulus
Compressive
Modulus (psi)
ASTM
D695
--- psi
--- GPa
To go back to contents,
click on
Contents
Flexural
Modulus (psi)
ASTM D790
At 73 F
--- psi
--- GPa
At 200 F
--- psi
--- GPa
At 250 F
--- psi
--- GPa
At 300 F
--- psi
--- GPa
Izod
Impact (ft-lb/in of notch)
ASTM D256
--- ft lb/in of notch
To go back to contents,
click on
Contents
Hardness
Rockwell ASTM D785
---
--
Shore D65 ASTM
D2240/D2583
---
Coefficient
of Linear Thermal Expansion
(10 exp-6 )in/in/C
---
(10 x exp –6) in/in /C
--- in/in /C
Deflection
Temperature under flexural load (F)
ASTM D648
264 psi ---
--- F
66 psi ---
--- F
To go back to contents,
click on
Contents
Thermal
Conductivity
(10 x exp –4)al cm/sec cm2 C
ASTM C177
--- (10 x exp –4) cal cm/sec cm2
--- cal cm/sec cm2
Specific
Gravity
ASTM D792
---
To go to Density /Specific Gravity Values,
click on
Density
Water
Absorption
(1/8 in thick specimen) (%)
ASTM D570
24 hr --- 1.4%
Saturation
3.3 %
Dielectric Strength v/mil
(1/8 in thick Specimen; short time)
--- v/mil
To
go back to the top of this page, click on
Top
**************************************
Copyright 2002 by Roger D.
Corneliussen
No part of this transmission is to be
duplicated, in any manor, or forwarded by
electronic mail without the express written
permission of Roger D. Corneliussen
**************************************
Number of visits since 4/3/2000: